B curve vs C curve MCB: for AC MCBs using the IEC/EN 60898-1 classification, the magnetic operating band is 3–5 times rated current for B and 5–10 times for C. Both still need suitable overload protection and breaking capacity. B is the lower-inrush option; C can accommodate a larger starting peak, but it also needs enough fault current to disconnect within the required time. Choose from the load data and the exact device curve, rather than replacing a tripping B breaker with C automatically. This guide explains the comparison for panel builders, contractors and technical buyers.
B curve vs C curve: magnetic trip range and selection table
| Check | B curve MCB | C curve MCB |
|---|---|---|
| Magnetic operating band for IEC/EN 60898-1 AC MCBs | 3–5 × In | 5–10 × In |
| Illustrative 16 A magnetic band | 48–80 A | 80–160 A |
| Starting-current question | Will the documented starting pulse enter the B operating band? | Does the C curve clear the actual starting pulse without compromising fault disconnection? |
| Fault-current question | Check the exact curve against the minimum fault current and required time. | Repeat the fault check; a higher magnetic threshold may rule C out. |
| What does not follow from the letter | No automatic increase in cable ampacity or breaking capacity. | No automatic increase in cable ampacity or breaking capacity. |
Basis for the AC classification: BEAMA Guide to Low-Voltage Circuit-Breaker Standards, section 3.3.1. In means rated current. The 16 A figures are arithmetic examples calculated from those ranges, not model-specific SUTON ratings. DC devices and devices declared to other standards require their own manufacturer data.
Worked comparison: B16 and C16 are both 16 A devices
Multiply the rated current by the magnetic-band limits: B16 gives 16 × 3 to 16 × 5 = 48–80 A; C16 gives 16 × 5 to 16 × 10 = 80–160 A. These are screening bands, not exact trip points. A short start pulse near a band boundary must be compared with its duration and the full manufacturer curve. The calculation does not say that either device may supply these currents continuously.
Suppose a load starts with a brief high current while its normal running current remains within the circuit design. Changing from B16 to C16 might improve starting tolerance, but that alone is not an approval. The designer must also check the cable, supply characteristics and fault at the remote end of the circuit. If the minimum fault current cannot meet the required disconnection time with C16, solve the underlying load or circuit problem instead of masking it with a less sensitive curve.
Replacing a curve: check the assembly as well as the circuit
A replacement breaker must match the approved board arrangement, terminals and connection system. Physical fit is insufficient. Ask the assembly manufacturer to confirm the proposed device; the BEAMA bulletin on safe selection of devices in assemblies explains why compatibility needs evidence. Request the exact SUTON catalogue number and declared curve with the enquiry, rather than assuming every product in a series has the same characteristic.
For higher starting-current duties, compare C curve and D curve MCBs. For the axes and tolerance bands behind this decision, see how to read a circuit breaker trip curve.
Standards and safety references: IEC 60898-1, IEC 60947-2, OSHA 1910.303 and OSHA 1910.333. Use the edition and local adoption required by the project.
Define the circuit duty before choosing the breaker
Begin with the source and load, not the breaker catalog. Record nominal and maximum system voltage, frequency, phase arrangement, earthing system, normal current, duty cycle and the way the load starts or switches. Identify motors, transformers, LED drivers, power supplies, capacitors and other equipment that can create a short current peak. A low steady-state current does not guarantee a low inrush, and a large inrush does not by itself justify a slower protective characteristic.
Next record conductor material, cross-section, insulation temperature, installation method, grouping, ambient temperature and route length. The breaker must protect the conductor under the adopted design rules. If a proposed change reduces unwanted trips but allows the conductor to remain exposed to damaging current for too long, it is not a valid solution.
Separate overload, starting current and short-circuit behavior
Overload protection deals with current above normal load that persists long enough to heat conductors and equipment. Starting or inrush current is usually brief and expected. Short-circuit protection addresses a much higher fault current that must be interrupted within the device rating and the required time. These regions overlap on a time-current graph, so the review must use both current and time.
Plot or compare the expected load envelope with the breaker tolerance band. The load should remain to the non-operating side during acceptable operation, while damaging overload and the minimum credible fault must fall within the required operating region. Use the complete tolerance band rather than a single ideal line. Verify that the available fault current does not exceed the device’s declared breaking capacity at the installed voltage.
Read the exact manufacturer information
Family names and front labels are not a complete specification. Obtain the datasheet and instructions for the exact catalog number, poles, trip unit and accessories. Check rated operational voltage, rated current, frequency, utilization conditions, breaking capacity, reference ambient temperature, conductor range, terminal torque, mounting orientation and environmental limits. For adjustable equipment, record the sensor or rating plug and every active setting.
Do not substitute a C curve simply to stop tripping. Confirm that the available fault current can operate it quickly enough. When the product data does not cover the intended duty, ask the manufacturer for a written application statement or select a device with declared suitability. Do not create a rating by combining unrelated values from several brochures.
Check maximum and minimum fault current
The maximum prospective fault current tests whether the breaker can interrupt the fault safely. The minimum fault current tests whether the selected protective characteristic will operate quickly enough at the remote end of the circuit. Both matter. A choice that survives the maximum fault but cannot clear a lower remote fault within the required time remains unsuitable.
Use a current short-circuit study that reflects transformer data, source configuration, cable impedance, parallel paths and operating modes. Standby generators, photovoltaic systems, UPS equipment and alternative bus configurations can change the result. Record the study revision used for the final selection.
Coordinate upstream and downstream protection
Compare the proposed device with upstream and downstream breakers, fuses and protective relays. Decide where selective operation is required and over what fault-current range. Two devices with different current ratings can still operate together if their instantaneous regions overlap. Conversely, a tested manufacturer combination may provide backup protection beyond the downstream device’s standalone rating.
Use exact curves and manufacturer selectivity or cascading tables. Confirm voltage, device variants and settings match the published combination. State whether the result is full selectivity, partial selectivity to a declared current, or backup protection. These are different claims and should not be used interchangeably.
Account for the panel environment
The air around the breaker may be warmer than the room. Heat from neighboring devices, restricted ventilation, enclosure solar gain and continuous loading can raise the local temperature. Altitude can affect cooling and dielectric performance. Use manufacturer correction data for the exact product and assess the complete assembly rather than applying an unverified universal factor.
Check clearances, mounting, conductor bending space and access for inspection. Terminals must accept the planned conductor type, number and cross-section. Use the declared preparation method and tightening torque with a controlled tool. A breaker can be electrically suitable but still be a poor panel choice if the terminal or installation arrangement cannot be executed reliably.
Common selection mistakes
- Choosing from normal load current while ignoring inrush and duty cycle.
- Increasing the current rating or slowing the curve only to stop tripping.
- Confusing continuous-current rating with breaking capacity.
- Assuming an AC rating automatically applies to DC or another frequency.
- Using a generic curve instead of the exact model tolerance band.
- Ignoring minimum fault current and required disconnection time.
- Claiming selectivity or cascading without exact combination evidence.
- Copying settings, torque or derating values from a similar-looking product.
Commissioning and verification
Before energization, verify device identity, poles, markings, settings, accessories, conductor placement, terminal work, barriers and labels. Compare the installed configuration with the approved schedule and study. For adjustable trip units, use the test method required by the project and manufacturer. Record as-left settings so a later inspection can detect unauthorized changes.
Electrical work can expose people to shock and arc-flash hazards. Establish an electrically safe work condition whenever required. Identify all sources, isolate them, apply the approved lockout procedure and verify absence of voltage with suitable equipment. Energized measurements may be performed only by qualified people under the site risk-control process.
Information to include in an RFQ
Send the supplier the system voltage and frequency, AC or DC duty, poles and neutral arrangement, continuous load, starting or inrush data, maximum and minimum fault current, required breaking capacity, conductor details, enclosure temperature, altitude, coordination objective, accessories and documentation requirements. Ask for exact datasheets, curves, dimensions, wiring diagrams and combination tables.
For a matching product discussion, review the relevant SUTON breaker product page. Use the circuit breaker types guide as the parent overview, and compare the separate guides on breaking capacity, selectivity and commissioning.
Educational video: circuit breaker fundamentals
This neutral engineering explainer supports the operating-principle discussion. It does not replace project calculations or manufacturer instructions.
Frequently asked questions
What is the difference between a B curve and a C curve MCB?
For IEC/EN 60898-1 AC MCBs, B has a magnetic operating band of 3–5 times rated current and C has a band of 5–10 times. Selection also requires the exact time-current curve, load inrush, cable protection and fault-current checks.
Can I replace a B16 MCB with a C16 to stop startup trips?
Only after a qualified design review confirms assembly compatibility, starting-current tolerance, conductor protection and the required fault-disconnection time. The same 16 A rating does not make the change automatically suitable.
Does a C curve MCB allow more continuous load than a B curve?
The curve letter does not increase the rated current. A B16 and a C16 are both nominally 16 A devices, subject to their manufacturer data and environmental corrections.
Final review checklist
Confirm the exact circuit duty, conductor protection, load envelope, maximum and minimum fault current, breaker curve or settings, breaking capacity, coordination evidence, environmental corrections, terminal arrangement and commissioning record. Resolve every missing input before approving the device. A defensible selection is one another engineer can reproduce from the saved drawings, calculations and exact manufacturer documents.